10 Tell-Tale Signs You Must See To Buy A Door Lock Change

How to Do a Door Lock Change

Changing your door lock is an easy and affordable way to improve the security of your home. However, the process is not for everyone. It requires a certain amount of patience and expertise.

You must replace the cylinder that is located within the knob's body. The cylinder recognizes the key when it is placed into the lock.

Remove the old lock

First, you must remove the old lock. This is a relatively easy procedure, but there are some things to keep in mind. First, make sure that the lock you choose to install is the right size for the door you have. This will ensure that it fits properly and does not create a gap around the latch or deadbolt plug.

After you've removed the latch plate look for two screws or bolts on the inside of the casing, which secure the casing and halves of the lock. Unscrew them using a screwdriver, then pull the lock out of the door. If you have a mortise locking system, there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw with the help of a screwdriver.

You should also take the deadbolt and latch plug from the hole in the door jamb. Install the new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the door's edge to ensure that your new lock will be able to fit.

Many reasons could cause you to replace the door lock, including being concerned that someone else may have the key, or you are welcoming an incoming roommate. You could save money if you take the lock off yourself instead of hiring for a professional. It's much easier than most people imagine and can be done in just a few moments.

Remove the trim and handle of your door. With a flat screwdriver pry off the trim. You will be able twist off most of it, and in some cases the handles could come off entirely. Then, look for a tiny pinhole on the inside and insert a straightened paper clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look for another small tab in the interior of the upvc window lock repair, and press it with a flat screwdriver. After the spindle has been removed, you can remove the cylinder and the housing.

Making a decision on a new locking system

When it comes time to pick the right lock for your home you have a variety of choices. Think about the various kinds of locks and choose one that is in keeping with the design of your door. Take into consideration the backset, which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, a small hole at the edge of your door's frame. Also, be sure to choose a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded most locks for doors to give you an idea of their durability and how difficult it is to pick them or disable them. A lock of grade 3 could be ideal for a peaceful apartment complex in the country, while locks of grade 1 may be better suited to the busy streets near a storefront.

Most smart door replacement locks for double glazed windows require a digital code to open. If you're concerned about hacking or other security issues, consult with a professional locksmith or your local police department for assistance.

Replacing the cylinder

You can easily replace damaged or broken door lock cylinder using an easy DIY project. The key is to select the right cylinder, and follow the directions that are included with it. First, take off the knob or handle if it is present. Then with a screwdriver unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, you can reach the screws that secure the cylinder and remove them using the flat-head screwdriver. The cylinder is then gently pulled out of the door.

Make sure you measure the length of your new cylinder prior to installing it. With an instrument, measure the distance between the cylinder's center and the left and right sides. Purchase a new cylinder which has the same measurements. This will stop the cylinder from snapping, which can occur when the door is kicked out or when the key sticks inside.

If you have a upvc window replacement lock cylinder, insert it in the door and turn the key. This will align the cylinder with your carrier which is located usually on the outside of the lock. You can then loosen the set screws that should be just a couple of turns inside the head. If there is a screw located on the outside of the case that holds the door, you will need to remove it.

After removing the lock cylinder after which you can replace it with a new lock by sliding the new cylinder into the case and tightening the set screw. You should also reinstall the piece that connects the cylinder to the stem for the lock indicator, which you can do by pulling up three small tabs on back of the cylinder using needle-nose pliers. Attach the smaller bracket to the back of the cylinder. Then, you should reinstall the latch plate and strike plate, as well as the retaining rings that are connected to the top of the lock cylinder.

Installing the new lock

If you're replacing an old lock, you should start by measuring the width of your door. Most locksets for residential use have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This will require longer screws as well as an extended spindle extension or the tail piece for door knobs.

The majority of double glazing window locks Repairs come with a detailed instruction booklet to help you install the new hardware. Take the time to read the instructions prior to beginning the process to make sure that you are following all of the necessary steps. The manual will also give you an idea of the level of expertise required to accomplish the task. You may want to ask a friend who has experience changing locks for help if you are changing a lock the first time.

Before installing the new lock, it's an excellent idea to put tape over the openings of the old hardware. This will stop the screws from falling through the holes, and also protect any tiles you might have put in. It will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with the masking strip or gaffer tape, but you can use any tape you own.

After taking off the screws that connect the lock's interior to the exterior and take the lock off immediately. This should be done swiftly to avoid the lock from accidentally closing and damaging the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the right position, which will be indicated by an arrow. Then, slide the latch plate over the bolt and secure it in the correct position.

Screw the deadbolt into the jamb of the door. Test the deadbolt by throwing it a few times to verify that it extends all way into the strike plate and is fully secure. If you're using an electronic smart lock, make sure to follow the included instructions to program it. This requires downloading an application and registering your e-mail address, verifying you identity and connecting to the wireless network to add your device.