15 Gifts For The Repairs To Upvc Windows Lover In Your Life

Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain and are durable and long-lasting. Unlike timber and aluminium, they are not susceptible to rust or rot.

It is important to clean and oil UPVC windows and doors on a regular basis. This will reduce unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, making it very dangerous and potentially fatal. It is crucial to take the time to make sure that you're doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace, and they typically fit into frames that were previously in use very easily. If windows with double panes are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this situation, it is necessary to purchase plastic spacers in order to make sure that the new pane fits into the window frame.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass yourself. It is also recommended to lay down a dropcloth before you start working on the glass so that any shards will fall on the fabric rather than on the floor where they could be trampled upon and cause further damage.

It's a good idea to tape the gap once the glass is removed. This will keep drafts and water from entering your property until a professional arrives to fix the window. This will also act as a barrier, deterring any intruders from getting access to your home. If the gap is particularly large, you might be interested in the security door with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber sash windows. However, with time, they can suffer from a variety of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts or even security. It is crucial to act immediately if you discover that your upvc window repair windows are falling down.

To fix a sagging window you can try to reposition the hinges. To do this, you'll need to open the window so that you can access the frame. Then, you can remove the hinges on the top and bottom using a screwdriver and adjust them clockwise or counter-clockwise. Close your window to check the fit after having repositioned your hinges. If you're satisfied with the fit, tighten the screws until they stay in the right place.

If you can't reposition the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to loosen. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window waterproof and draughtproof.

uPVC handles may also become loose. Most often this is due to screws that have become loose over time. However, it could also happen because the handle mechanism has been worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. First, you'll need to close the window and then perform an experiment fitting. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and then reverse the mechanism back into the position it was in.

3. Water Leaks

It is crucial to take action if you awake each day to find a smoky wall and wet floors. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be done by any skilled DIYer. Based on the severity of the problem the caulking that was used up may need to be removed before a new layer of caulk is applied. When it is time to uPVC repair, you should be careful not to over-caulk. This can make your window more difficult to clean and decrease its energy efficiency.

Verify that the drainage holes have no debris in them, and also that the sill pan has been properly angled to drain away from the window. In more serious cases, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. The fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to note that if the leak originates from the glass of your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sagging. Again this can easily be corrected by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open with ease, it may be the hinges that are at the fault. They can be easily repaired by any DIYer who is skilled and can be completed in just a few minutes.

Like any mechanical part hinges will wear out over time. It's very simple to change the hinges on a window but it's much easier if someone helps you hold the frame.

It is also important to verify that the uPVC hinges are opened and closed in the correct direction. You can do this by checking for the arrows on each hinge, this indicates the direction in which the window should open.

The problem can be caused due to opening the window in the wrong way or a faulty installation in the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be more than happy to give you suggestions.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window open and close more easily. It can also lower the possibility of a window sticking and prevent corrosion. This must be done at a minimum once a year. WD40 and other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by several different things. The hinges may also become unbalanced due to wear, causing an opening where the sash meets frame. They can be repaired by giving them good clean, but in the event that they are beyond repair it may be necessary to have them aligned or replaced. The interlock may be disaligned. This happens on the hinge's side and may need to be cleaned. In certain instances it might be necessary to replace them.

The next most common cause of draughts is the window seals. They are susceptible to being worn out or damaged over time, and allow air to escape through the gaps. Replacing these with high-quality weatherstripping will help to stop draughts. Another alternative is to replace the window with low-emissivity glass. which will help regulate indoor temperatures and will lessen the possibility of draughts.

Lastly, one of the most effective ways to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes that are filled with some kind of filler. They can be positioned on top of your windowsill. These will help to keep cold air out and keep your home warm and cosy!

Your upvc windows can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. However, it is important to realize that windows last for a certain period of time and they may reach the point when it's more economical to replace them than repair them. If you have any problems with your upvc window it is recommended to speak with an expert as soon as you can.