10 Erroneous Answers To Common Repairs To Upvc Windows Questions Do Yo…

Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain and are durable and long-lasting. They are not susceptible to get rotten or rusty like aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will reduce unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and may even be fatal. It is essential to make sure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the replacement will usually fit inside the frame that was previously installed easily. However when you have double pane windows that are held in place by internal beading it will be more difficult to get rid of the existing panes and install new ones. In this instance you'll need find some plastic spacers that will help the new pane to fit correctly into the window frame.

Wearing eye protection and thick gloves is a must if you plan to remove the glass by yourself. It is also a good idea to lay down a dropcloth before you start working on the glass to ensure that any shards will fall onto the fabric instead of landing on the floor, where they could be trampled on and cause further damage.

It's a great idea tape the gap once the glass is removed. This will keep drafts and water from entering your property until a professional arrives to repair the window. This will also act as a barrier that will prevent any intruders from getting access to your home. If the gap is large, you may be interested in an alarm door that comes with an integrated window as this will offer the best of both worlds.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash windows. In time, they could be affected by a variety of issues such as sliding. A window that is sagging can cause problems with light, draughts and even security. If you notice that your uPVC window repair is beginning to sag it is important to act swiftly to stop the issue from getting worse.

To fix a sagging window you can try repositioning the hinges. First, you'll need to open the windows so you can get at the frame. After that, using the screwdriver, you'll be able to unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have moved your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they stay in position.

If you aren't able to move the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity over time, causing them to loose their elasticity. If this happens, it's crucial to replace the seal as fast as possible so that your uPVC windows are waterproof and draught-proof.

UPVC handles can also become loose. The majority of the time it is due to screws that have come loose over time. However, it could occur because the handle mechanism has worn out. Luckily, it's not difficult to fix a loose uPVC window handle yourself. First, you'll need to close the window and perform an experiment fitting. The corner joints of the sash need to align with the casing joint. If it isn't you can use a screwdriver to loosen the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is crucial to take action if you wake up every morning to find mouldy walls and floors that are wet. Water leaks through windows can cause structural damage to your home and hinder your ability to control the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or missing.

This is a fairly simple fix that can be completed by any skilled DIYer. Depending on the severity of the issue is, the old caulking might need to be removed. It is crucial to remember that when it is about uPVC window repairs, you should avoid the temptation to "over-caulk in order to make the area harder to clean and decrease the efficiency of your energy usage.

It is important to check that the drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious instances, you may need to think about replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double-glazed window, it is more likely that the problem is with the seal rather than the frame. This can be easily repaired by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or if it opens in a breeze. These are easily repaired by any skilled DIYer and are usually completed in just a few minutes.

Like all mechanical parts hinges are prone to wear out over time. It is an easy process but it can be easier when you have a person to assist in holding the frame in place.

Check that the uPVC hinges are closed and open in the correct direction. Look for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window a certain way or due to improper installation in the factory. Sending us a picture via our website will often solve the issue. We are more than happy to provide advice.

It is also essential to lubricate the hinges on a regular basis. Applying a light engineering lubricant to the hinges is a great way to do this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more easily. It can also stop corrosion and reduce the possibility of sticking. It is recommended to do this once a year. WD40 and other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in windows made of upvc window repairs can be caused by different factors. Firstly the hinges, again because of wear and tear, could become misaligned. This causes an opening to appear between the sash and the frame. They can be repaired by giving them good cleaning, but when they're beyond repair, it may be necessary to get them realigned or replaced. In addition, the interlock could be misaligned. This is located on the hinge's side and might require to be cleaned. In some cases it is possible to replace these.

The seals may wear out or become damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help to regulate indoor temperatures, and reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler which can be put on top of your window sill. These will keep your home warm by blocking cold air.

The windows made of upvc can keep providing excellent insulation and security for your home with a little regular maintenance and repairs. However, it is important to recognise that all windows have a lifespan and there may come the point when it's more economical to replace them than fix them. If you are experiencing problems with your upvc windows, it is always recommended to seek help from a professional immediately.