The 10 Most Terrifying Things About Car Key Button Repair

Car Key Button Repair

A broken car key button is frustrating. It is possible to contact a 24-hour locksmith Service for assistance or to purchase a new remote.

However, you might be able to save money by repairing a worn-out key fob instead of replacing it. This is especially true if an old switch or damaged contacts are at the root of the issue.

Battery

If the buttons on your key fob aren't responding to pressing, it could be an obvious sign that the battery is dying or nearing the end of its life. Fortunately replacing the battery is an easy task that can be done on your own instead of hiring a locksmith or dealer to complete the task for you.

Locate the battery compartment first. The battery compartment is usually located on the back of the key fob, and may be concealed behind a cover that slides out or an open button that opens the access point. When the compartment is open then look for the small button-cell battery. It's usually the shape of the shape of a coin and is has a plus and the minus symbol. Take the old battery out, and replace it with a new one. Check that the plus and symbol are aligned correctly.

Once the battery is in place, close the compartment and snap the two halves of the key fob together. Before closing the door make sure to align and snap the pieces into the correct position. Press any of the buttons to ensure that they work properly.

If your remote keyfob still isn't working after replacing the battery, there may be other problems that require a different kind of repair. Damage to the physical structure caused by dropping the fob into a puddle for instance could cause it to stop working altogether. It could also be due to a malfunction with the internal electrical system or the need to be deprogrammed. Try to figure out if the problem is with your key fob by using these other automotive troubleshooting methods.

Switches

There are various types of switches found in the car key button repair key fob according to the year and model. The older model keys usually have an additional chip that is visible in the case, whereas newer keys are more advanced and operate by sending signals to the car key repair company. Whatever the model of key, the buttons on the key can get worn down or damaged during normal use. They can become difficult to press or unresponsive. If you try to force the button to work it could cause further damage, and could even prevent the key from being able to start your vehicle in the future.

If your key doesn't appear to be working, first try changing the battery. If this doesn't work, you may have to clean the key fob or adjust its switches. Since these tiny electronic switches spend a lot of time being tossed around and tangled, they are more likely to break down than the larger parts of your key.

The switches are made of rubber, and are coated with an electrically conducting film that can wear down over time. Fortunately, they're tiny and inexpensive to replace. The old ones are soldered onto the circuit board so you will need to carefully remove them without damaging anything else. You can then solder the new ones into and reassemble your fob.

An effective way to protect your car key fob from becoming ruined is to avoid using it for longer than a couple of hours at a time and also to not leave it in visible locations in areas where to repair car key remote it is visible. Also, try to locate a safe place to store your key when you're not making use of it.

If you've already tried cleaning your key fob and replacing the battery, but the problem persists it's probably time to think about hiring the services of a locksmith. A professional can check the frequency of your key to determine whether it's still able communicate with your vehicle, open and replace micro switches, alter cases and much more.

Outer Case

If the buttons can't move freely in the case, they may become stuck or break. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it might be necessary to remove the case. If the contacts that the buttons touch don't fit well or are worn out, adjusting them may be the only solution to fix the problem.

Some keys are equipped with buttons made of rubber that be worn out over time. The buttons made of rubber can become difficult to press when they stretch, and nails could cut them. In this situation, the key may fail and it's time to replace the case or the buttons. This repair involves removing the remote, locating the button switches on the circuit board, heating up the solder and carefully removing them. New buttons are then soldered to the circuit board. The case is then reassembled and the horse shoe key blade piece is attached. The new buttons must be securely fitted into the case to keep them from falling out.

Inner Case

Since your key fob is likely be tossed around and sometimes be accidentally pressed and the buttons inside may be damaged or stuck over time. Utilizing metallic tape and a hole punch, you can fix this problem in the event your car isn't at home and the key fob isn't working and you are unable to open the doors, but not to start the engine. This quick fix could allow you to safely make it back to your vehicle and complete your journey.