The Most Hilarious Complaints We've Heard About Fiat Panda Key Fob Rep…

Reasons Your Fiat 500 Key Fob Won't Work

A Fiat 500 key fob allows you to easily open doors and start your vehicle. There are a myriad of reasons the fob may stop working. This includes a dead battery, water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement fiat 500 key replacement cost Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). It includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs have a restricted operating range, and should be within only a few feet from the vehicle in order to function. If you're far away from your vehicle, and you press the key fob button the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a brand new one of a reputable brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your Fiat van keys 500. The car will flash its parking lights and the key fob will operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it might have water damage that stops it from communicating with the receiver module inside your car. Water damage can happen in a number of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to pull the moisture out. If this fails, you'll require your fob to be reprogrammed either by an auto locksmith or a dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can be particularly harmful to the circuit board of the fob, causing it to short out and eventually die. In the event that you let your fob get wet, it's not an ideal idea, but if you drop it in the water in a cup or do not remember to remove it from your pants pocket before running the washer, don't give up hope.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob to see if it is functioning. If the fob doesn't work it could need to be reprogrammed. This is usually done by a professional or dealer auto locksmith.

If the key is newer and hasn't been programmed to your vehicle it is likely to need to be replaced completely. This is a straightforward process which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your car. The locksmith also needs to reprogram your fob into the vehicle's system. This is a cost-effective and quick process that could be completed in the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote's range is of 30 feet. So should you be too far from your car it won't respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board problem. Reprogramming your fob can resolve this issue. You can find instructions on how to do this on the majority of vehicles by searching YouTube or checking out the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of hardware or software problems. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software may require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin the key fob could not be able to receive or transmit the signal due to interference. This can happen when the key fob is located near a radio transmitter (cell phones or Fiat Van Keys radar detectors) or any other source of electromagnetic radiation. The key fob could not work because of a problem with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming it, or using a spare key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electric current, and also restart the computer in your car. This can help you get your key fob to function again. If the issue continues, you should speak with an expert technician. They will be able to determine the root of any issues.