The 10 Scariest Things About Repair Car Keys

How to repair car keys [site]

Car keys might seem tiny and insignificant, but they are vital for the proper operation of your vehicle. The cost of replacing a traditional or modern transponder car keys can be upwards to $200.

There are methods to repair car remote control key your car keys at home with a fraction of the cost. This article will cover the most common car keys problems and the DIY solutions to fix them.

Dead Key Fob Battery

The remote car key repairs key fobs that are included with cars make it simpler than ever to open the trunk, doors and tailgate. The battery in this device is susceptible to dying. Fortunately, there are some techniques that can be employed to fix this issue in the event of a need.

First, check if the car is in ignition mode. If it is, the battery of the key fob may be drained instead of dead. To test this, press the button on the fob against the ignition button on the vehicle. If it works, the battery is likely fine and needs to be changed.

To replace the battery within the fob, the case open using a screwdriver. Be cautious not to apply too much pressure because this could cause the fob to break in two. If the fob doesn't seem to be coming easily, try putting your pry tool in multiple places on the outside of the case.

Once the fob is open take out the mechanical key and open the electronic portion of the car. Insert the new battery and then snap back the shell. If the key fob isn't working after this, there could be a bigger problem with the remote start system that requires a professional to diagnose. A reputable mechanic will be able help you if this is the situation. If you require assistance with your car, you can contact roadside assistance.

Broken Key Ring

If your key fob isn't functioning because the ring broke, there are a few things you could try. First, you must check to see if the broken piece is still in the ignition. If it's still there it, remove it without damaging either the ignition lock or the door lock. Call a locksmith if you have difficulty getting rid of the key. They have specialized tools that allow you to safely remove a damaged key from the ignition.

Another reason for a broken car key remote repair key is the corrosion of the circuit board or plastic frame. Clean the board with rubbing alcohol and a cotton swab. This will get rid of the corrosion and prevent damage to the contact pads.

If your key isn't working because the ring broke, you may be able fix it using a sturdy wire or nail to seal the hole. Superglue can also be used to repair a broken ring. After cleaning the ring with a wet cloth, apply a small amount superglue to the ends of the nail or wire. Let the pieces dry and then press them together. These DIY solutions can appear appealing, but they're really just a stopgap measure. For long-term repairs, it's recommended to work with a professional locksmith. They have the knowledge and tools to fix the broken key quickly and effectively. They can replace the battery and reprogram the key fob in the event of need.

Broken Key Blade

Some key blades can break from a lot of wear and tear. If this occurs, you must purchase a new one. This problem isn't nearly as serious as you believe at first. The main problem is that the blade has snapped away from the case.

Spraying lubricant into the keyhole is one way to fix the problem. You can then employ pliers or tweezers grab the broken end of the key and pull it. You could also make use of a magnet if the key is magnetic. Use a magnet as a aid to you remove the key, but be careful to not damage the lock tumbler.

If you are unable to take the broken piece of key, contact an emergency locksmith. They're equipped with special tools that permit them to safely remove keys without causing damage.

You can also use super glue to repair a snapped key. Apply a small amount glue to the edges of the break and press them together. Then, wait until the glue dries before you insert your key into the lock. But this method isn't very secure and you may need to repeat the process multiple times before it works. Additionally the super glue might not be enough to keep the key in place. This is more of a temporary measure than an option that can last.

Broken Plastic Loop

If the plastic loop is damaged it can render the key useless. This is a relatively easy fix. You can make use of wire or a nail for finishing to replace it. Drill two holes into the broken plastic loop for each end of the nail or wire. Cut the nail or wire to key repair service width and put a drop of superglue on each hole. Put the nail or wire into the holes to seal them and let it dry.

A locksmith who sells replacement shells is another option. They can remove the programmable part of your key, transfer it to the new shell, and cut an entirely new blade for less than the full replacement cost.

This is not the best solution, but will help you get back on the road again if your key has split in half. It's not easy to repair if the key blade is in the ignition, however. You can try using hair clips, a needle or an extractor tool to pull the broken part of the ignition, but it's risky if not cautious. The best solution is to call an expert locksmith who has tools for safely removing damaged keys from the ignition. You can also have a new key that is made using the correct cuts to fit the ignition of your car.

Broken Master Key

If a key breaks inside the lock, you'll have to find it before it gets completely destroyed. There are a few techniques you can use, including using lubricants as well as tools such as needle nose pliers and tweezers to grab a fragment of the key that has been broken and remove it.

Spray the inside of the lock with WD-40 or graphite powder. You can also use the hacksaw blade method that involves moving the blade along the sides of the broken key, and then grasping a few of its 'teeth. If you're successful then you should be in a position to cut the damaged key.

Many hardware stores carry the spiral key extraction tool. It is a thin flexible rod with spiral threads that can be inserted into the keyway, and then bent to form the broken part of the key. Once it has gotten caught on the serrations you can twist the bar in a circle and then pull it up against the broken section of the key.

It's worth attempting to remove a broken master key before calling a professional locksmith. If you are unable to get the piece out, it's time to call in the big guns and let a locksmith cut you a new key and reprogram it using your car's transponder.