24 Hours To Improve Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 makes it simple to open doors and start your vehicle. However, there are a variety of reasons why the key fob might stop functioning. These include a dead coin battery or damage to the receiver module, issues, or interference.

This listing is for a NEW replacement fiat 500 duplicate key Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob that isn't working. Modern key fobs have a limited operating range, and must be within a few feet of the car to operate. If you're far from your vehicle and press the key fob button, the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery in the coin cell (Part number CR2032) with a brand new one from a trusted brand such as Panasonic, Duracell, or Energizer. They are available at your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing close to your Fiat 500. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your key fob still doesn't work even after replacing the battery, there may be water damage that hinders it from interacting with the module in your vehicle. Water damage can occur in a number of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If that doesn't work your fob may require reprogramming by an experienced auto locksmith or the dealer.

Water Damage

While the fob has some rubber seals that keep water from the chip's electronic circuit it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and then end up dying. In the event that you let your fob get wet, it's not an ideal idea, but if you drop it in the water in a cup or fail to remove it from your pants pocket prior to running the washer do not give up hope.

First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Test the fob afterward to check if it's working. If the fob doesn't work it could need to be reset. This is usually done by an auto locksmith or dealer.

If the key is more recent and has not been programmed to your vehicle It is likely that it needs to be replaced completely. A professional automotive locksmith can complete this simple process. The locksmith will need to cut the key to match the ignition in your vehicle. They'll also have to program the fob into the system of your car. This is a low-cost and quick process that could be completed on the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far from your car it will not respond to your commands. You can remedy this by moving your remote closer to your car until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will fix the problem. You can find instructions on how to get a new fiat 500 key to do this for all vehicles by searching YouTube or looking through the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it could prevent the battery from sitting properly and can cause the remote to malfunction.

In rare instances, the fob could be out of connection with your vehicle as a result of hardware or software issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases the software may require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin, the key fob may not be receiving or transmitting a signal due to interference. This could happen when the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob could not function because of a problem with the buttons or water damage, or damage to the internal chips.

If the key fob failed to work one day suddenly, or after trying everything you can at home to resolve it e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands that are then processed by the vehicle.

Luckily, there is an easy method to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then, reconnect the battery. This will remove any remaining electricity, and allow you to restart the car's computer. This will help you get your key fob to work again. If the problem persists it is recommended that you consult an expert technician. They can identify the root cause of your problems.